Radiant Commercial Solar Logo
Call

Commercial Industrial Solar in Perth, WA

Industrial sites run heavy daytime loads: motors, compressors, refrigeration and production lines that draw hard while the sun is up. Radiant Commercial Solar designs rooftop systems built around that pattern, so generation lands when your plant is actually running. We work across Perth industrial zones from Osborne Park and Malaga to Kewdale, Welshpool and Henderson.
Request a Quote

What's Included in Our Industrial Solar

1

Roof and Structural Assessment

We assess the roof before anything else. Industrial sheds vary widely, and the profile, whether Kliplok, Trimdek or insulated panel, decides the mounting method and fixings used. We check purlin spacing, sheet condition and load capacity so the array sits safely without compromising the roof's warranty or weatherproofing.
2

Load-Matched System Design

With the load profile settled, we specify the array, string layout and inverter count to suit the roof and your demand. We balance panel orientation across available spans, set inverter sizing against expected generation, and plan cable runs back to the switchboard so the installed system performs close to its design on paper.
3

Access, Walkways and Compliance

Large rooftop arrays need safe access and clear egress. We design walkways, maintenance paths and fire separation into the layout so the system meets compliance and your staff can reach plant on the roof. Isolation points and signage are placed for safe operation and future servicing.

Industrial Solar Across Different Facilities

Warehouse Solar Systems

Warehouses offer large uninterrupted roof spans well suited to solar panels, though loads are often lighter and spread across lighting, dock equipment and racking. These buildings suit sizeable arrays where there is daytime activity to use the output. We work with the available span and the roof structure to lay out a system that fits the building.

Factory and Manufacturing Solar

Factories and manufacturing plants carry some of the heaviest continuous loads: motors, presses, compressed air and process heat. These sites suit solar power well because demand runs hard during daylight. We plan the array around production areas and roof access so the build works alongside a busy floor rather than getting in its way.

Logistics and Distribution Centres

Logistics and distribution centres run long operating hours with forklifts, conveyors, cold rooms and charging bays. The large roof areas suit sizeable solar systems. We plan layouts around skylights, plant and roof penetrations so the array fits the real roof, and stage work to keep dock and yard operations moving.

Cold Storage Facility Solar

Cold storage facilities carry a constant refrigeration load that runs day and night, making them strong candidates for solar power. Many use insulated panel roofs that need specific mounting detail to protect the panel skin. We design the fixings and array to suit that construction without compromising the roof’s thermal performance.

How an Industrial Solar Project Runs

Load Analysis and Metering Review

We start with your interval data and bills to read how your site consumes power across days and shifts. This load profile shows how much solar the site can genuinely use before we specify a single panel, so the system is sized to your real demand rather than a generic estimate.

Site Inspection and Proposal

Our team inspects the roof, switchboard and available grid capacity, then prepares a design and written proposal. You see the proposed layout, expected generation against your load, and the practical constraints we found, so you can make the decision with the full picture in front of you.

Installation Around Production

Installation is staged to keep your site operating. We coordinate roof work, cabling runs and switchboard connection around your production schedule, booking any required shutdown in advance. Most rooftop work proceeds without interrupting the floor below, and critical tie-ins are timed for quiet periods.

Commissioning and Monitoring

Once installed, we test and commission the system, confirm it generates as designed, and set up monitoring so you can track output and consumption. We walk your team through the platform and explain what healthy performance looks like, so faults or drops in output are easy to spot.

Plan Your Industrial Solar System

If you run a factory, warehouse or cold store in Perth, we can read your load profile and show what solar could realistically offset. Send us your recent bills or metering data and we'll assess your roof and switchboard, then provide a written proposal. Contact us to start the conversation.
Request a Proposal

Why Load-Matched Solar Pays Off

Generation That Matches Daytime Load

The strongest return comes when solar energy is used on site rather than exported. Industrial sites draw heavily through daylight hours, so a system matched to that profile offsets expensive grid power exactly when plant, motors and refrigeration are running, giving a far better outcome than oversizing against roof space alone.

Lower and More Predictable Bills

Energy is a major fixed cost for industrial operations. Offsetting a large share of daytime consumption reduces your exposure to rising tariffs and demand charges, making power costs easier to budget. The savings are steadiest where production hours line up with generation, which is common across Perth industrial sites.

Resilience in Perth Conditions

Perth's long, bright summers suit solar generation, but industrial zones bring dust and fallout that build on panels over time. Designing with accessible walkways and quality components keeps output stable and makes cleaning and servicing straightforward, protecting the system's performance across its working life.

Common Questions About Industrial Solar

Ready to Book?

Request a Quote and we’ll confirm your timeline and scope—then keep you updated right through to handover.

Get In Touch

Fill out the form below and our team will reach out to you soon: